Sales: 512-635-8793
Customer Service: 512-635-8824
Fax: 512-650-3663
FREE Ground Shipping on most orders over $50*

Victor-Reinz Gaskets 20mm dowel full head set



Our Price: $472.18

472 reward points

Model: HS54579
Shipping Weight: 20lbs
Manufactured by: Ford



Add to Cart:


DESCRIPTION: Victor-Reinz 20mm Complete Head Set for Ford 6.0L Powerstroke diesel. This kit includes all of the gaskets and seals to do a complete top-end engine rebuild.

INCLUDES SEALS FOR:
2) Air Pump
1) Air Sensor
2) Cylinder Head
4) Cylinder Head Plug
1) EGR Valve
2) EGR Valve
2) EGR Valve
4) EGR Valve
1) EGR Cooler
1) EGR Cooler
1) EGR Tube
2) Exhaust Manifold
1) Fuel Filter
1) Fuel Filter O-Ring
1) Fuel Filter O-Ring
1) Fuel Filter O-Ring
8) Fuel Injection O-Ring
8) Fuel Injection O-Ring
8) Fuel Injection O-Ring
1) Fuel Injector
1) Fuel Injector
1) Fuel Pressure Regulator
2) Fuel Pressure Regulator
2) Fuel Pressure Regulator
1) Fuel Pressure Regulator
2) Fuel Pressure Regulator
1) Fuel Pressure Regulator
1) Fuel Pressure Regulator
1) Fuel Pressure Regulator
8) Injector Nozzle Washer
8) Injector Tube Seal
2) Intake Manifold
3) O-Ring
1) Oil Cooler
1) Oil Cooler
1) Oil Cooler
1) Oil Filler
1) Oil Filler
2) Oil Pipe
2) Oil Pipe
2) Oil Pipe
3) Oil Pump Cover
1) Oil Pump Inlet
1) Oil Pump Inlet
1) Oil Pump O-Ring
1) Oil Pump O-Ring
2) Throttle Body
2) Turbo Drain
1) Turbo Oil Drain
1) Turbo Oil Drain
2) Valve Cover
2) Valve Cover
22) Valve Cover Grommets
32) Valve Stem Seals
4) Washer
2 Washer

APPLICATIONS: Fits 2003-2007 Ford 6.0L Powerstroke Diesel Trucks with 20mm dowel pins

NOTES:
Dowel Pins not included with this set.
Most 2003-1/15/2006 trucks that have not already had head gaskets replaced most likely have 18mm dowel pins. If so please use part #: VR-HS54450 instead.

NOTE:

Clevite Engine Parts Tech Bulletin
“Surface Finish Specifications for Victor Reinz gaskets.”

Cast iron block and cast iron head using VR2000 or Nitroseal should have an acceptable finish of RA 60*-120 with a desirable finish of RA 80.

Aluminum head with a cast iron block using VR2000 or Nitroseal should have an acceptable finish of RA 20*-60 with a desirable finish of RA 30.

Aluminum or cast iron block or head using the MLS gasket should have an acceptable finish of RA 20-60 with a desirable finish of RA 30.

*Victor Reinz does not recommend a finish smoother than minimum figures with composite and solid core gaskets as it could result in a failure.

Desirable Flatness: .002” in 6”
Max Waviness: keep below 200 RA

Note: Victor Reinz gaskets will seal a wide range of surface finishes depending on the condition of a number of surface variables. Adhering to the above recommendations will insure the rebuilder an extremely reliable gasket sealing-surface. The acceptable range indicates the min-max numbers for the surface, while the desirable finish number can be considered a target to shoot for during the machining process. Other things beside surface finish affect gasket sealing. Fastener quality and condition, condition of the threaded hole in the block, tightening procedure and specifications, proper lubrication of the fastener and proper measuring tools all play a part on the ultimate success or failure of the gasketed joint!

Victor Reinz recommends following the manufacturer’s recommended cylinder head installation procedure.

A surface finish that exceeds maximum specifications creates microscopic “peaks and valleys” in the mating hardware. When these “peaks and valleys” exceed specifications, the gasket is unable to conform to the irregular shape even with proper bolt torque or clamp load. These “peaks and valleys” can create leak paths for both fluids and combustion gases. This happens because the gasket is not supported adequately by the “rough and wide surface finish”.

Kind regards,

Duane Bethke
MAHLE Clevite Inc.
Gaskets (Team Coordinator II)

1240 Eisenhower Place, Ann Arbor, Michigan 48108-3282 USA
Phone: 1 (734) 975-7963, Fax: 1 (734) 975-7825
duane.bethke@us.mahle.com, http://www.mahle-aftermarket.com



Copyright © 2018 Storm Automotive Technologies. Powered by Zen Cart